Please refer to xorg.conf(5) for general configuration
details. This section only covers configuration details specific to this
driver.
The driver auto-detects the chipset type, but the following
ChipSet
names may optionally be specified in the config file
N'34'DeviceN'34'
section, and will override the auto-detection:
-
"mga2064w", "mga1064sg", "mga2164w", "mga2164w agp", "mgag100", "mgag200",
"mgag200 pci", "mgag400", "mgag550".
The G450 is Chipset "mgag400" with ChipRev 0x80.
The driver will auto-detect the amount of video memory present for all
chips except the Millennium II. In the Millennium II case it defaults
to 4096 kBytes. When using a Millennium II, the actual amount of video
memory should be specified with a
VideoRam
entry in the config file
N'34'DeviceN'34'
section.
The following driver
Options
are supported:
-
- Option N'34'ColorKeyN'34' N'34'integerN'34'
-
Set the colormap index used for the transparency key for the depth 8 plane
when operating in 8+24 overlay mode. The value must be in the range
2-255. Default: 255.
-
- Option N'34'HWCursorN'34' N'34'booleanN'34'
-
Enable or disable the HW cursor. Default: on.
-
- Option N'34'MGASDRAMN'34' N'34'booleanN'34'
-
Specify whether G100, G200 or G400 cards have SDRAM. The driver attempts to
auto-detect this based on the card's PCI subsystem ID. This option may
be used to override that auto-detection. The
mga
driver is not able to auto-detect the presence of of SDRAM on secondary
heads in multihead configurations so this option will often need to be
specified in multihead configurations. Default: auto-detected.
-
- Option N'34'NoAccelN'34' N'34'booleanN'34'
-
Disable or enable acceleration. Default: acceleration is enabled.
-
- Option N'34'AccelMethodN'34' N'34'stringN'34'
-
Chooses between available acceleration architectures. Valid options are
XAA
and
EXA.
XAA is the traditional acceleration architecture and support for it is very
stable. EXA is a newer acceleration architecture with better performance for
the Render and Composite extensions, but the rendering code for it is newer and
possibly unstable. The default is
XAA.
-
- Option N'34'NoHalN'34' N'34'booleanN'34'
-
Disable or enable loading the "mga_hal" module. Default: the module is
loaded when available and when using hardware that it supports.
-
- Option N'34'OverclockMemN'34'
-
Set clocks to values used by some commercial X Servers (G100, G200 and G400
only). Default: off.
-
- Option N'34'PciRetryN'34' N'34'booleanN'34'
-
Enable or disable PCI retries. Default: off.
-
- Option N'34'RotateN'34' N'34'CWN'34'
-
-
- Option N'34'RotateN'34' N'34'CCWN'34'
-
Rotate the display clockwise or counterclockwise. This mode is unaccelerated.
Default: no rotation.
-
- Option N'34'ShadowFBN'34' N'34'booleanN'34'
-
Enable or disable use of the shadow framebuffer layer. Default: off.
-
- Option N'34'SyncOnGreenN'34' N'34'booleanN'34'
-
Enable or disable combining the sync signals with the green signal.
Default: off.
-
- Option N'34'UseFBDevN'34' N'34'booleanN'34'
-
Enable or disable use of on OS-specific fb interface (and is not supported
on all OSs). See fbdevhw(4) for further information.
Default: off.
-
- Option N'34'VideoKeyN'34' N'34'integerN'34'
-
This sets the default pixel value for the YUV video overlay key.
Default: undefined.
-
- Option N'34'TexturedVideoN'34' N'34'booleanN'34'
-
This has XvImage support use the texture engine rather than the video
overlay. This option is only supported by G200 and later chips, and only
at 16 and 32 bits per pixel.
Default: off.
-
- Option N'34'OldDmaInitN'34' N'34'booleanN'34'
-
This forces the driver to use the old DMA initialization path for DRI.
Use this option only to support a older version of the DRI driver with
a newer DRM (version 3.2 or later). This option also disables the use
of direct rendering on PCI cards.
Default: off.
-
- Option N'34'ForcePciDmaN'34' N'34'booleanN'34'
-
This forces the use of PCI DMA even if AGP DMA could be used. This
option is primarily intended for testing purposes, but it could also
be used on systems with a buggy or poorly function AGP implementation.
Default: off.